Technische bijstand
Wij willen duidelijkheid verschaffen over de belangrijkste technische vragen die kunnen opduiken over de werking van onze producten en de stappen die nodig zijn voor de montage ervan.
Lade Vertex
Here we will show you how to assemble a Vertex/Concept drawer with the Tecnotool machine, you will see that it is very simple and fast. Thanks to its measurement positioner and its easy handling you will see that it will be very convenient for you.
Here we will show you how to assemble a Vertex/Concept drawer with the Tecnotool-Pro machine; you will see that it is very simple and very fast thanks to its automatic side stapling system. You will be able to assemble large series of drawers.
The formula is: internal module width -70. For this particular case, the internal width of the module will be 800 - 32 = 768 mm. From this measurement we subtract 70 to get the length to cut the profiles = 666 mm.
Yes, as long as you have a 13 mm wide square railing , or a straight rib with a minimum internal height of 135 mm and width of 13 mm. If I have a 800 mm wide module, and a 16 mm thick side panel.
It is only necessary to connect the machine to air with a pressure of 7-8 kg/cm2
The following video shows how you can easily assemble the Vertex inner drawer.
Yes, for the assembly of the rectangular under sink insert it is necessary to make a 90º angle straight machining cut, although it is recommended to make a machining cut with a radius of 20 mm.
The following video shows how you can easily assemble the Lokbox mechanism.
Yes, the Lokbox mechanism is used to fasten the bottom of the drawer to the front part without preventing adjustment of it. It is compatible with the Concept, Slim and Vantage-Q drawers or any drawer. It is especially recommended for very wide drawers used in the furnishings of kitchens, bathrooms, lounges and even inside wardrobes. However, you need to take into account that the installation dimensions change. See diagram.
In order to assemble a kitchen drawer with hinges on the unit doors (hinged doors) it is necessary to use hinges with an opening angle of 165ª or to use spacers, doing so means there will be enough space to pull out the drawer.
The spacer is intended for assembling a drawer inside a unit with a hinged door. It can also be used in cabinet interiors with a sliding door with loss of opening.
This 25 mm thick spacer is compatible with the following interior drawers: Vertex, Concept and Vantage.
They are calculated for a side thickness of 16 mm.
Yes, the spacers that are user for assembling kitchen Vertex, Concept and Vantage drawers are the same as hinges on unit doors (hinged doors).
No, the minimum unit depth is the same (depth + 5 mm).
No, the assembly and positioning of the rails is the same in both the push and soft close versions.
It depends on the type of front panel you use for the interior drawer:\- Aluminium front. This is fitted onto guides at the usual distance, 37 mm in the 4th hole of the guide.\- Particle board front. The thickness of this board must be added to the 37 mm of the 4th hole of the guide.In other words, if the front is 19 mm thick, the guide must be fastened at 37 + 19 = 56 mm at the 4th hole of the guide.
Yes, it is the same profile that is used for all four drawer heights. The 178 mm height panel, however, also needs the front rail profile.
The RAL code of the anthracite grey finish of the sides of the Vertex drawer is approximately 7043. The RAL code of the grey finish of the sides of the Vertex drawer is approximately 7045. The RAL code of the white finish of the sides of the Vertex drawer is approximately 9003.
Yes, for example, if we want to assemble a drawer for a module width of 500 mm, we have to use the existing code for the 600 mm module and cut the base and rear panels to the width indicated by the formula. Width of module interior - 19 mm.
The following video shows how you can easily assemble the Vertex runners.
The following video shows how you can easily to disassemble the Vertex drawer.
The following video shows how you can easily to adjust the Vertex drawer.
The following video shows how you can easily assemble the Vertex drawer.
